Commit 9d46b770 authored by Maxime Ripard's avatar Maxime Ripard Committed by David S. Miller

arm: sunxi: Revert changes merged through net-next.

This reverts commits 2c0cba48 ("arm: sun8i: sunxi-h3-h5: Add dt node
for the syscon control module") to 2428fd0f ("arm64: defconfig: Enable
dwmac-sun8i driver on defconfig") and 3432a86e ("arm: sun8i:
orangepipc: use internal phy-mode") to 5a79b4f2 ("arm: sun8i:
orangepi-2: use internal phy-mode") that should be merged
through the arm-soc tree, and end up in merge conflicts and build failures.
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent f1efece4
......@@ -57,7 +57,6 @@
aliases {
serial0 = &uart0;
/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
ethernet0 = &emac;
ethernet1 = &xr819;
};
......@@ -104,13 +103,6 @@
status = "okay";
};
&emac {
phy-handle = <&int_mii_phy>;
phy-mode = "internal";
allwinner,leds-active-low;
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>;
......
......@@ -46,10 +46,3 @@
model = "FriendlyARM NanoPi NEO";
compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
};
&emac {
phy-handle = <&int_mii_phy>;
phy-mode = "internal";
allwinner,leds-active-low;
status = "okay";
};
......@@ -54,7 +54,6 @@
aliases {
serial0 = &uart0;
/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
ethernet0 = &emac;
ethernet1 = &rtl8189;
};
......@@ -109,13 +108,6 @@
status = "okay";
};
&emac {
phy-handle = <&int_mii_phy>;
phy-mode = "internal";
allwinner,leds-active-low;
status = "okay";
};
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
......
......@@ -52,7 +52,6 @@
compatible = "xunlong,orangepi-one", "allwinner,sun8i-h3";
aliases {
ethernet0 = &emac;
serial0 = &uart0;
};
......@@ -98,13 +97,6 @@
status = "okay";
};
&emac {
phy-handle = <&int_mii_phy>;
phy-mode = "internal";
allwinner,leds-active-low;
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
......
......@@ -53,11 +53,6 @@
};
};
&emac {
/* LEDs changed to active high on the plus */
/delete-property/ allwinner,leds-active-low;
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins_a>;
......
......@@ -52,7 +52,6 @@
compatible = "xunlong,orangepi-pc", "allwinner,sun8i-h3";
aliases {
ethernet0 = &emac;
serial0 = &uart0;
};
......@@ -110,13 +109,6 @@
status = "okay";
};
&emac {
phy-handle = <&int_mii_phy>;
phy-mode = "internal";
allwinner,leds-active-low;
status = "okay";
};
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
......
......@@ -83,12 +83,6 @@
#size-cells = <1>;
ranges;
syscon: syscon@1c00000 {
compatible = "allwinner,sun8i-h3-system-controller",
"syscon";
reg = <0x01c00000 0x1000>;
};
dma: dma-controller@01c02000 {
compatible = "allwinner,sun8i-h3-dma";
reg = <0x01c02000 0x1000>;
......@@ -285,14 +279,6 @@
interrupt-controller;
#interrupt-cells = <3>;
emac_rgmii_pins: emac0 {
pins = "PD0", "PD1", "PD2", "PD3", "PD4",
"PD5", "PD7", "PD8", "PD9", "PD10",
"PD12", "PD13", "PD15", "PD16", "PD17";
function = "emac";
drive-strength = <40>;
};
i2c0_pins: i2c0 {
pins = "PA11", "PA12";
function = "i2c0";
......@@ -389,32 +375,6 @@
clocks = <&osc24M>;
};
emac: ethernet@1c30000 {
compatible = "allwinner,sun8i-h3-emac";
syscon = <&syscon>;
reg = <0x01c30000 0x104>;
interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
resets = <&ccu RST_BUS_EMAC>;
reset-names = "stmmaceth";
clocks = <&ccu CLK_BUS_EMAC>;
clock-names = "stmmaceth";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
mdio: mdio {
#address-cells = <1>;
#size-cells = <0>;
int_mii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
clocks = <&ccu CLK_BUS_EPHY>;
resets = <&ccu RST_BUS_EPHY>;
};
};
};
spi0: spi@01c68000 {
compatible = "allwinner,sun8i-h3-spi";
reg = <0x01c68000 0x1000>;
......
......@@ -257,7 +257,6 @@ CONFIG_SMSC911X=y
CONFIG_STMMAC_ETH=y
CONFIG_STMMAC_PLATFORM=y
CONFIG_DWMAC_DWC_QOS_ETH=y
CONFIG_DWMAC_SUN8I=y
CONFIG_TI_CPSW=y
CONFIG_XILINX_EMACLITE=y
CONFIG_AT803X_PHY=y
......
......@@ -40,7 +40,6 @@ CONFIG_ATA=y
CONFIG_AHCI_SUNXI=y
CONFIG_NETDEVICES=y
CONFIG_SUN4I_EMAC=y
CONFIG_DWMAC_SUN8I=y
# CONFIG_NET_VENDOR_ARC is not set
# CONFIG_NET_CADENCE is not set
# CONFIG_NET_VENDOR_BROADCOM is not set
......
......@@ -67,14 +67,6 @@
};
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
phy-mode = "rgmii";
phy-handle = <&ext_rgmii_phy>;
status = "okay";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
......@@ -85,13 +77,6 @@
bias-pull-up;
};
&mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
......
......@@ -46,20 +46,5 @@
model = "Pine64+";
compatible = "pine64,pine64-plus", "allwinner,sun50i-a64";
/* TODO: Camera, touchscreen, etc. */
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
phy-mode = "rgmii";
phy-handle = <&ext_rgmii_phy>;
status = "okay";
};
&mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
/* TODO: Camera, Ethernet PHY, touchscreen, etc. */
};
......@@ -70,15 +70,6 @@
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&rmii_pins>;
phy-mode = "rmii";
phy-handle = <&ext_rmii_phy1>;
status = "okay";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
......@@ -89,13 +80,6 @@
bias-pull-up;
};
&mdio {
ext_rmii_phy1: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
......
......@@ -129,12 +129,6 @@
#size-cells = <1>;
ranges;
syscon: syscon@1c00000 {
compatible = "allwinner,sun50i-a64-system-controller",
"syscon";
reg = <0x01c00000 0x1000>;
};
mmc0: mmc@1c0f000 {
compatible = "allwinner,sun50i-a64-mmc";
reg = <0x01c0f000 0x1000>;
......@@ -287,21 +281,6 @@
bias-pull-up;
};
rmii_pins: rmii_pins {
pins = "PD10", "PD11", "PD13", "PD14", "PD17",
"PD18", "PD19", "PD20", "PD22", "PD23";
function = "emac";
drive-strength = <40>;
};
rgmii_pins: rgmii_pins {
pins = "PD8", "PD9", "PD10", "PD11", "PD12",
"PD13", "PD15", "PD16", "PD17", "PD18",
"PD19", "PD20", "PD21", "PD22", "PD23";
function = "emac";
drive-strength = <40>;
};
uart0_pins_a: uart0@0 {
pins = "PB8", "PB9";
function = "uart0";
......@@ -406,26 +385,6 @@
#size-cells = <0>;
};
emac: ethernet@1c30000 {
compatible = "allwinner,sun50i-a64-emac";
syscon = <&syscon>;
reg = <0x01c30000 0x100>;
interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
resets = <&ccu RST_BUS_EMAC>;
reset-names = "stmmaceth";
clocks = <&ccu CLK_BUS_EMAC>;
clock-names = "stmmaceth";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
mdio: mdio {
#address-cells = <1>;
#size-cells = <0>;
};
};
gic: interrupt-controller@1c81000 {
compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
......
......@@ -191,7 +191,6 @@ CONFIG_RAVB=y
CONFIG_SMC91X=y
CONFIG_SMSC911X=y
CONFIG_STMMAC_ETH=m
CONFIG_DWMAC_SUN8I=m
CONFIG_MDIO_BUS_MUX_MMIOREG=y
CONFIG_MESON_GXL_PHY=m
CONFIG_MICREL_PHY=y
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment